Det verkar som att du har inaktiverat Javascript i din webbläsare. Vissa funktioner på den här sidan kommer inte att fungera, såvida du inte har loggat in.

Ser du något fel?

STEVAL-POEL45W1

Bilder är endast för referens
Se produktspecifikationer

Mouser nr:

511-STEVAL-POEL45W1

Tillverk: Nr.:

STEVAL-POEL45W1

Tillverk:

STMicroelectronics

Beskrivning:

LED-belysningsutvecklingsverktyg Power over Ethernet (PoE) powered 45 W LED driver with Bluetooth Low Energy (BLE

Komplettera din design

Datablad:

STEVAL-POEL45W1 Datablad (PDF)

Mer information

Lär dig mer om STMicroelectronics STEVAL-POEL45W1

Leveransavisering:

Mouser säljer för närvarande inte den här produkten i din region.

Tillgänglighet

Lager:: Ett oväntat fel har inträffat. Försök igen senare.

.hidden-for-nojs { display: none; } .pull-right-nojs { justify-content: flex-end; }

Produktattribut	Attributvärde	Välj attribut
Tillverkare:	STMicroelectronics
Produktkategori:	LED-belysningsutvecklingsverktyg
Leveransrestriktioner:	Mouser säljer för närvarande inte den här produkten i din region.
RoHS-direktivet:
Produkt:	Development Boards
För användning med:	PM8805, LED6000, SPBTLE-1S
Serie:	STEVAL-POEL45W1
Förpackning:	Bulk
Märke:	STMicroelectronics
Produkttyp:	LED Lighting Development Tools
Fabriksförpackningskvantitet:	1
Underkategori:	Development Tools
Enhetens vikt:	41 g

Hittade produkter:

Markera minst en kryssruta för att visa liknande produkter

Markera minst en kryssruta ovan för att visa liknande produkter i denna kategori.

Attribut som valts: 0

Filtrera dokument:

Datablad

STEVAL-POEL45W1 Datablad (PDF)

TARIC:: 8517620000
CNHTS:: 8543709990
USHTS:: 8517620090
JPHTS:: 851762090
ECCN:: 5A002.A.2

STEVAL-POEL45W1 Evaluation Board

STMicroelectronics STEVAL-POEL45W1 Evaluation Board is a PoE-enabled constant current LED driver with BLE control. The board features a PM8805 PoE interface, LED6000 LED driver and BLUETOOTH® module SPBTLE-1S. The PM8805 embeds a double active bridge, a hot swap MOSFET, and an IEEE802.3bt-compliant PoE interface. The LED6000 is a step-down monolithic switching regulator designed to source up to 3A_DC current for high power LED driving. The 250mV typical RSENSE voltage drop enhances the efficiency. Digital dimming is implemented by driving the dedicated DIM pin. The SPBTLE-1S is a BLUETOOTH low Energy System-on-Chip application processor certified module. It is compliant with BT specifications v4.2 and BQE qualified.

31FL323x LED Lighting Development Boards

ISSI 31FL323x LED Lighting Development Boards are development tools that evaluate ISSI multi-channel LED drivers. LED drivers are electrical circuits used to power light-emitting diodes. The fully assembled and tested board is powered by the Arm® Cortex®-M3 or 80C51 (IS31FL3235A-QFLS2-EB) with a 5V operating supply voltage. The evaluation boards have multiple display modes.

IS31LT3360 Demonstration Board

ISSI IS31LT3360 Demonstration Board is a fully assembled and tested PCB that uses the IS31LT3360 continuous mode inductive step-down converter. This ISSI board is designed to drive single or multiple series connected LEDs. This performance is achieved efficiently from a voltage source higher than the LED voltage.